PIC16F1946-I/PT【PDF 67/478 页】IC MCU 8BIT FLASH 64TQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3870

63页 64页 65页 66页 [67页]68页 69页 70页 71页

2010-2012 Microchip Technology Inc.

DS41414D-page 159

PIC16(L)F1946/47

15.0 TEMPERATURE INDICATOR

MODULE

This family of devices is equipped with a temperature

circuit designed to measure the operating temperature

of the silicon die. The circuit’s range of operating

temperature falls between -40°C and +85°C. The

output is a voltage that is proportional to the device

temperature. The output of the temperature indicator is

internally connected to the device ADC.

The circuit may be used as a temperature threshold

detector or a more accurate temperature indicator,

depending on the level of calibration performed. A one-

point calibration allows the circuit to indicate a

temperature closely surrounding that point. A two-point

calibration allows the circuit to sense the entire range

of temperature more accurately. Reference Application

Note AN1333, “Use and Calibration of the Internal

Temperature Indicator” (DS01333) for more details

regarding the calibration process.

15.1

Circuit Operation

Figure 15-1 shows a simplified block diagram of the

temperature circuit. The proportional voltage output is

achieved by measuring the forward voltage drop across

multiple silicon junctions.

Equation 15-1 describes the output characteristics of

the temperature indicator.

EQUATION 15-1:

VOUT RANGES

The temperature sense circuit is integrated with the

Fixed

Voltage

Reference

(FVR)

module.

See

Section 14.0 “Fixed Voltage Reference (FVR)”

for

more information.

The circuit is enabled by setting the TSEN bit of the

FVRCON register. When disabled, the circuit draws no

current.

The circuit operates in either high or low range. The high

range, selected by setting the TSRNG bit of the

FVRCON register, provides a wider output voltage. This

provides more resolution over the temperature range,

but may be less consistent from part to part. This range

requires a higher bias voltage to operate and thus, a

higher VDD is needed.

The low range is selected by clearing the TSRNG bit of

the FVRCON register. The low range generates a lower

voltage drop and thus, a lower bias voltage is needed to

operate the circuit. The low range is provided for low

voltage operation.

FIGURE 15-1:

TEMPERATURE CIRCUIT

DIAGRAM

15.2

Minimum Operating VDD

When the temperature circuit is operated in low range,

the device may be operated at any operating voltage

that is within specifications.

When the temperature circuit is operated in high range,

the device operating voltage, VDD, must be high

enough to ensure that the temperature circuit is

correctly biased.

Table 15-1 shows the recommended minimum VDD vs.

range setting.

TABLE 15-1:

RECOMMENDED VDD VS.

RANGE

15.3

Temperature Output

The output of the circuit is measured using the internal

Analog-to-Digital Converter. A channel is reserved for

the temperature circuit output. Refer to Section 16.0

“Analog-to-Digital Converter (ADC) Module”

for

detailed information.

High Range: VOUT = VDD - 4VT

Low Range: VOUT = VDD - 2VT

Min. VDD, TSRNG = 1

Min. VDD, TSRNG = 0

3.6V

1.8V

Note:

Every time the ADC MUX is changed to

the temperature indicator output selection

(CHS bit in the ADCCON0 register), wait

500

sec for the sampling capacitor to fully

charge before sampling the temperature

indicator output.

TSEN

TSRNG

VDD

VOUT

To ADC

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式